Honeysuckle dryer：When the drying starts, the temperature is controlled at 30°C-35°C. After 2 hours, the temperature is increased to about 40°C. After another 5-10 hours, the temperature is increased to 45°C-50°C and maintained for 10 hours. Finally, the temperature is increased to 55°C-58°C, and the maximum shall not exceed 60°C, and the total drying time is 24 hours...

Phnom penh rose dryer：After the flowers are placed in the drying room, the temperature gradually rises from 35°C, 38°C, 42°C, 46°C, and 50°C for 2 hours. After the flowers are set, the temperature rises to 55°C-60 °C, 11 hours, and finally bake at 65°C for 1 hour to increase the fragrance...

Astragalus dryer：Use the heat pump low-temperature drying method, the drying temperature should be 70°-80°C, and the thickness of the goods should not exceed 4 cm. After drying, sieve the medicine scraps, the total ash content should not exceed 4.5%, and the acid-intolerant ash content should not exceed 1.0%...

Coptis dryer：The main problem in the current initial processing of Coptis is to adopt a reasonable drying process to obtain good quality dried Coptis. The higher the drying temperature of Coptis, the faster the drying speed, but the quality of Coptis drying will decrease...

Cotton pad dryer：Cotton pad drying is divided into four stages, the first stage: comprehensive mode, set the drying temperature to 70°C, humidity to 35%, and drying time to 1 hour. The second stage: still in the comprehensive mode, set the drying temperature to 70°C, humidity to 25%, and drying time to 1 hour...

Soybeans are dried in a variety of ways. Generally speaking, they are dried more naturally in the sun, because the harvest season for soybeans is usually late summer or autumn when there is usually more sunny days and less rainfall, so there is a chance for them to dry naturally, however, it takes longer for soybeans to dry naturally, and the degree of drying is not completely the same. If the amount is large, plus the harvest season is overcast and rainy, you can use the heating drying method. Even the use of professional drying equipment for drying...

Hericium erinaceus dryer：After harvesting, Hericium erinaceus needs to be sorted according to size in time. After sorting, it is ready to be plated and dried. Before drying, the drying room must be preheated so that the temperature in the drying room reaches 40°C. When a large number of Hericium erinaceus is sent to the mushroom room, the range of 30°C-35°C can be maintained...

Brown sugar dryer：Cut the brown sugar bricks into cubes, put them in the tray, put them in layers in the material rack, pay attention to the distance between the layers, push the material truck into the drying room, and start the temperature and humidity control system. You can only heat up in an hour without dehumidification, because in the first stage of work, the humidity in the drying room is very low...

Because people have a large demand for jerky, small-scale production can not meet the demand for jerky, so it is very important to use a dehydrator to make jerky.
First of all...

Sweet potato vermicelli dryer：The vermicelli after the overnight cold storage has frozen into ice cubes on the outside. At this time, it is pushed into the sweet potato vermicelli drying room for heating and dehumidifying drying. After the water in the sweet potato vermicelli melts and evaporates, the roots begin to harden...

Mahogany dryer：When the moisture content of wood is higher, lower temperature and higher humidity must be used. Wood moisture content is about 30% is a critical period, and drying must be done gently. When the moisture content of wood from different piles differs greatly, it must be treated in a balanced manner...

Russula dryer：The russula are put on the grill and sent to the drying room for baking. Place the large and thick ones with high moisture content on the upper layer, and the small and thin ones with low moisture content on the lower layer. Generally placed 8 to 10 floors. If it is placed too much, the heating temperature of the upper, middle and lower materials will be uneven...